The advantages of the terminal related to the automatic terminal machine and the advantages of automatically wearing the waterproof plug terminal machine.

Has the following advantages:

 

1. The welding pin is made of copper alloy, and the welding pin has no dirt to ensure long-term reliability of welding.

 

2. The clamping body and the welding pin are mechanically decoupled, that is, because the clamping body and the welding pin are not connected together, the torque when tightening the screw is not transmitted to the solder joint.

 

3. The end of the welding pin is shortened and made easy to install.

 

4. With cooling channel.

 

5. Tinned solder pins for easy soldering.

 

6. Large wiring capacity, can be used to a variety of wiring needs.

 

7. The solder pins are quadrangular and the ends are shortened and tapered. When piercing the weld hole, it can prevent random transformation. Use solder bath to dissolve into the solder hole.

1. Mold height scheduling: Loosen the punch compression screw and use a small round rod to change the dispatching screw (six aliquots on the circumference), clockwise up and counterclockwise down (0.25 mm per aliquot) ), adjust the punch to the proper orientation, and then tighten the punch to tighten the screw (that is, arrange the core crimp height).

 

2. The upper inner knife and the upper outer knife fall the difference scheduling: PVC pressing height micro-distribution, loosening the upper knife pressing screw, pulling out the rotation, from 1-8 a total of 8 guidelines, the larger the number, the higher the PVC blade height, each The height of the policy differs by 0.1 mm. Adjust to the appropriate position (ie, schedule the line crimp height).

 

3. Some scheduling of feeding: press the up and down keys to move the slider to the highest point, loosen the feeding rod fixing seat pressing screw, rotate the feeding scheduling screw (clockwise backward, counterclockwise forward), and send the terminal to the blade center. Scheduling the slider to the proper orientation is scheduled.

 

4. When the mute terminal machine starts the power switch, it is necessary to disengage the wrench.

 

5. It is necessary to adjust to the highest point before starting the punch.

 

6. Prevent several terminals from being pressed.

 

7. Admit that the voltage is normal (please install a voltage regulator) to ensure the service life of the machine.

 

8. For your safety, make sure your hands are off the machine to start the power operation.

 

9. When the operator adjusts the mold, it is necessary to make the machine in manual condition (ie the indicator light is red).

The terminal machine refers to a machine used for wire processing. It can press the hardware head to the wire end and then conduct it. The terminals that are driven out by the terminal machine are usually more convenient for connection. The two wires can be stably connected without soldering, and only need to be unplugged when disassembling.

 

The automatic terminal machine is a new equipment in recent years. It has a multi-functional machine, feeding, cutting, multi-functional machine stripping and crimping together, humanized and intelligent high-end technology products, which are suitable for large, medium and small. Enterprise, saving labor. In order to extend the life of the fully automatic terminal machine, we need to maintain it daily.

 

 The fully automatic terminal machine is capable of cutting, stripping and pressing the terminal. It has similar functions to the computer stripping machine, and has the function of peeling and pressing detection. There are mechanical terminal machines in the market (many are domestically produced). ) and computerized terminal machines (joint ventures and imports). The mechanical type is mechanically driven, and the stability and accuracy have certain dimensions. The computer type uses track and rail motion and runs with a servo motor. The stability and accuracy are excellent.

 

 The guide rails of the fully automatic terminal punching machine must have a lubricating oil hole at the top of each terminal for 1 hour, and generally 2-3 drops are suitable. In addition, the surface of the fully automatic terminal machine must be cleaned daily and excess grease. The main high-speed bearing terminals must be greased weekly. After using the fully automatic terminal machine after 3-6 months, it is necessary to check whether all parts (loss) need to be replaced with accessories such as belts, whether the mechanical locking screws are loose, and whether the spring is deformed.

 

 Breaking the traditional meaning of automatic maneuvering workflow layout, the line cutting, peeling, end, and twist line height are combined in a straight line. Since the various operating mechanisms are integrated in a straight line, the production time of a single electronic wire is reduced, and the production capacity is surprisingly several times higher than that of the conventional model.

For machines, poor contact has always been one of the main causes of failure, from small mobile phones to computers, to terminal machines, or to aviation equipment. For the computer, the fault of the contact is more than the memory stick.
 

For the automatic terminal machine, the poor contact is the metal conductor inside the terminal, which is the core zero of the terminal, which transmits the voltage, current or signal from the external wire or cable to the matching connector. On the contact piece. Because of its importance, we have a very high demand for it, which requires stable and reliable contact and good electrical conductivity.
 

For wire harness equipment such as single-head terminal machines, enterprises should consider the following factors when purchasing a silent terminal machine: the quality of the single-head terminal machine is good and the performance is stable. The high-precision, multi-functional, high-quality automation equipment is stable during use; the single-head terminal machine has a long service life, and after the mechanical equipment enters the production line, it will wear out after a long period of operation.
 

The length of the peeling opening of the fully automatic crimping machine is different: there are many common reasons for the different opening, such as the feeding roller is too tight or loose; in this case, you only need to use the roller fine adjustment to adjust the gap between the two wheels. So that the wire is not flattened and too slippery. If it is because the cutting knife is too shallow or too deep; then we use the cutter depth adjustment member to adjust the knife edge to the appropriate position, so as not to damage the copper wire and can peel off the rubber. If the opening is still different, replace the new cutting blade directly.
 

The surface quality of the part includes the surface roughness, the degree of hardening of the surface layer and the nature and size of the surface residual stress. The surface quality of the part has the properties of wear resistance, corrosion resistance, fatigue resistance, and the service life of the part. Great impact. Therefore, the surface quality requirements of parts working under high speed and heavy load are high, and the requirements of surface roughness are only indicated on the drawings of general parts. The arithmetic mean deviation of the contours of the surface roughness.

Under normal circumstances, in the normal operation of the fully automatic terminal machine, there are generally several common problems below, one is the poor contact of the terminal, one is poorly fixed and the insulation is poor.

1. Poor contact: The metal conductor inside the terminal is the specific core component of the terminal. It transmits the voltage, current or signal from the outer wire or cable to the corresponding contact of the matching connector. Therefore, the contact member must be structurally excellent and reliable, and in addition, it must have excellent holding force and electrical conductivity. If the structural design of the contact is unscientific or the material is selected incorrectly, it is caused by poor contact at the contact portion of the contact and its mating part.

2, poor fixation: In fact, the insulator not only plays the role of insulation, but also shows a very accurate alignment and maintenance for the contact device, while also having the installation positioning, locking and fixing on the top of the device, the fixation is poor, light It is harmful to the momentary power failure caused by reliable contact. Seriously, the product may be disintegrated. Because the design is not reliable, the material selection is wrong, and the poor selection of the molding process will result in poor fixation.

3. Poor insulation: Due to the appearance of the insulator of the automatic terminal machine and some metal extras inside, the dust and flux of the external surface are damp, and the organic material precipitation material and the harmful gas adsorption film and the outer water film are fused to produce ionic conduction. The same channel, moisture absorption, mildew, insulation material aging and other factors are caused by short circuit, low insulation resistance, leakage and breakdown, etc. The specific effect of the insulator is to maintain the correct position of the contacts, and Between the contact member and the contact member, the contact member and the housing are connected to each other for transport protection, so the insulator must have excellent electrical properties, especially with high density, miniaturized terminal blocks are widely used, and the reasonable wall thickness of the insulator is increased. The thinner it is, the more stringent requirements are placed on the precision and process of the mold.

The above is about the solution to the problem of automatic terminal machine wiring. I hope it can help you. If you want to know more about the automatic terminal machine, you can click on the website page of the automatic terminal machine to browse!

Now, no matter what sales we are still buying active terminal machines, we are more concerned about the brand, of course, so domestic brands can also be foreign. More and more users are beginning to pay attention to the brand effect, which is also the key to the competition of major manufacturers. Ruiyang’s initiative has become famous in the industry, and its brand value is far more than all.

 

More and more producers are driven by interests, and they start to viciously attack their opponents. As a seller, in addition to the ability to distinguish between authenticity and counterfeiting, we must put the quality function of Ruiyang active terminal machine in an important position to select specifications. The inner and outer rings of the steel ball bearing are unbalanced, which is one of the causes of heat generation. The imbalance between the inner and outer rings of the terminal machine may be due to machining. Because the base and end caps of the fully active terminal machine are separated, sometimes the bearing holes on the two end caps are not coaxial (ie, the center line is not on a line).

 

The mute terminal machine has too much or too little smooth oil, which is also a cause of heat generation. The bearing is used for a long time, the internal smooth oil is gradually reduced, so that the smoothness is not good, the friction loss is added, the bearing is heated, and the long-term oil shortage operation will constitute bearing damage. Too much oil or too thick oil can also cause the bearing to overheat. In addition, the smooth oil is mixed with hard grain impurities, the bearing is not cleaned, or the bearing is cleaned with dirty oil, so that sand and iron filings are left in the bearing, the mechanical friction of the bearing is added, the bearing is heated, and the impurities are caused by impurities. The bearing is easily damaged.

 

In addition, the installation of the fully active crimping machine is poor, the screws on the end caps are unevenly elastic, and there are dust and dirt on the mouth, which may also make the inner and outer rings unbalanced. If the inner and outer rings of the bearing are unbalanced, the steel balls and the inner and outer rings will be scraped to increase friction and generate heat. If there is no other reason, wipe the machine mouth and reinstall it, and tighten the screws one by one in the diagonal order. A small amount of error during processing can be improved by progressive active adjustment.

 

Cixi Hongsheng Machinery Equipment Co., Ltd. is a high-tech enterprise specializing in R&D and manufacturing of automated wire harness end processing equipment and non-standard automation equipment. After decades of development and technology precipitation, the company has domestic leading independent core technology, advanced production equipment and perfect management system. It has won the trust and support of domestic and foreign customers with excellent quality and good reputation. “Acer” won 86 national patents (18 of which were invention patents) and was recognized as a municipal key new product. The products were listed in Zhejiang Province’s first “machine substitution” advanced applicable equipment promotion catalogue. The company has passed the ISO9001 quality management system certification and has been recognized as a municipal-level enterprise engineering technology center, a municipal-level technology-based enterprise, and a national high-tech enterprise.