1. Stripping and trimming effect. It is necessary to carefully observe whether the wire after stripping of the automatic terminal machine will be stripped, the stripping is not aligned, the copper wire is damaged, the outer skin is scratched, and the wire has obvious twists and turns. Not the same length and so on. Of course, the length of the stripping and cutting length has an error value of 0.2 mm + (set length × 0.002 mm).

 

2, the effect of crimping the terminal, the quality of a fully automatic terminal machine is mainly depends on the effect of its crimping terminal, if the terminal it is crimped is defective, or does not overwhelm the copper wire, or the pressure interface is Loose, it will directly affect the quality of your product. This will be a fatal injury.

3, the speed of the automatic terminal machine, if the above two points are almost the same, the working speed of the automatic terminal machine will be its other secondary indicators. The enterprise chooses the automatic terminal machine mainly for its automation. If its speed is higher, it means that it will bring you higher efficiency. Of course, the premise is that the wire harness processed by the fully automatic terminal machine is a good product. .

When we use the terminal machine for the first time, we must remember that we must not start it ourselves. We must let experienced employees conduct guided operations and strictly prohibit the unintelligible personnel from operating the terminal machine. In addition, when we use the terminal machine for the first time, we must familiarize ourselves with the instructions for using the terminal machine. Because we are familiar with it, we can know the specific procedures for the use of the terminal machine.

 

In addition, when we use the terminal machine, we must install the knife by the designated personnel. Before loading the knife, we must manually compare the selected blades. If the comparison is correct, the knife can be installed. After the tool is completed, the hand test needs to be used. . At this time, we must first turn off the power of the terminal machine, press the touch button, use the special wrench to shake the main driven wheel, so that the terminal machine press stroke to the maximum, if the hand does not move, consider whether the pressure is too large or other problems, Check debug to OK. Before each operation, check each locking screw and confirm that it is not loose.

 

When the terminal machine replaces the terminal, the power must be disconnected before the replacement is performed. It is strictly forbidden to replace it during the operation of the machine.

 

Finally, after the production is completed, the good products and waste products are sorted out, and the environmental sanitation around the machine is cleaned. It is guaranteed that the next time the terminal machine is used, it will not cause a safety accident due to the residual of the scrap.

We know that full automation plays a big role in the enterprise, the market share of automatic terminal machines is getting higher and higher, and the degree of attention is also increasing. The use of tools is crucial when using terminal machines for production and processing. The vibration of the tool during the cutting process is mainly represented by a long length and a vibration phenomenon when the workpiece is thin.

 

Automatic terminal machine refers to a kind of wire processing, also known as automatic peeling and crimping machine. A new equipment has a multi-function machine, feeding, cutting, multi-functional machine stripping, crimping together, humanized and intelligent. High-end technology products, suitable for large, medium and small enterprises, saving labor.

 

Automatic terminal machine

 

The terminal machine refers to a machine used for wire processing. It can press the hardware head to the wire end and then conduct it. The terminals that are driven out by the terminal machine are usually more convenient for connection. The two wires can be stably connected without soldering, and only need to be unplugged when disassembling.

 

 

The remanufacturing of automatic terminal machine machinery can greatly alleviate the pressure on the environmental bearing capacity of industrial manufacturing. It aims to develop the development route of the engineering machinery remanufacturing industry from the remanufacturing industry and the construction machinery industry. From the path of industrial evolution, it can be found that the energy environment, economic environment, policy standards, market demands, and industrial networks together constitute the system architecture for remanufacturing high frontiers. The main purpose of establishing this system is to ensure the industrialization and scale of remanufacturing.

 

If the temperature of the fully automatic terminal machine is too high, it is caused by the long running time of the equipment, which is normal. Some of them may be due to some faults in the equipment, such as the imbalance of the inner and outer rings of the steel ball bearing or the amount of lubricating oil. Since the base and end cover of the fully automatic terminal machine are separately machined, the imbalance is highly likely to exist, so it is necessary to strengthen the inspection in this respect.

 

However, the fully automatic terminal machine can be used for the terminals that are not used, because there are many types of terminals, and the difference in shape and function determines the application field. How to determine whether the terminal needs to use the fully automatic terminal machine, it depends on the terminal need not need external force terminal to connect the terminal machine, if it is, you can use it.

Automatic terminal machine is a new equipment in recent years. It has a multi-function machine, feeding, cutting, multi-functional machine stripping and crimping together, humanized and intelligent high-end technology products, which are suitable for large, medium and small enterprises. , saving labor. In order to extend the life of the fully automatic terminal machine, we need to maintain it daily.

 

The automatic terminal machine is capable of cutting, stripping and crimping the wires. It has similar functions to the computer stripping machine, and has the functions of peeling and pressing detection. There are mechanical terminal machines in the market (mostly domestic) And computerized terminal machines (joint ventures and imports). Mechanical is a measure of mechanical transmission, stability and precision. The computer type uses track motion and runs with a servo motor, which is excellent in stability and accuracy.

 

During the processing of the terminal machine, there may be a situation of poor contact. Of course, the metal conductors in the contact of the entire terminal machine are all the main core components, and they are mainly from external power sources or cables. The voltage, current, or signal is transmitted to the surface of the connector that matches them to make the relevant processing contact. It is necessary to have more optimized structures. Only in this way can the operation be more stable and reliable, and they must be good. The electrical conductivity, so if the structural design of the contact is unreasonable, or the material selection is wrong, then basically the entire contact parts will have some poor contact.

 

The use of the tool is crucial in the production process using the terminal machine. The vibration of the tool during the cutting process is mainly manifested in the case where the length is long and the workpiece is fine. In the process of high-speed cutting, a large amount of noise is generated, which also causes harm to the human body. Correct and rational use of such a fully automatic terminal device can greatly reduce noise and reduce vibration.

 

The vibration of the automatic terminal machine can be divided into three modes: high frequency vibration, medium frequency vibration and low frequency vibration. There are many ways to reduce the vibration, such as using sharp tools and 90 degree tools for slender workpieces. Angle to cut, adjust the specific parameters of the cutting, and rationally arrange the process path of the cutting.

 

During the processing of the terminal machine, there may be a situation of poor contact. Of course, the metal conductors in the contact of the entire terminal machine are all the main core components, and they are mainly from external power sources or cables. The voltage, current, or signal is transmitted to the surface of the connector that matches them to make the relevant processing contact, so there must be more optimized structure, so that it can be more stable and reliable operation, and they must guarantee Good electrical conductivity, so if the structural design of the contact is unreasonable, or the material selection is wrong, then basically the contact parts will have some poor contact.

 

If there are some faults in the wiring problem of the terminal machine, it may be because their fixing is not particularly good. For a simple example, the insulator not only has good insulation effect, but more importantly, it can also give the whole terminal. The components of the machine provide a series of protection functions. At the same time, they also have the characteristics of installation and positioning. The functions of locking on the fixed equipment, and can not be fixed relatively light, may affect their instantaneous power-on function. Therefore, serious affirmation will also affect the disintegration of some other products. Therefore, in the actual design process, there may be unreliability, or the tendency of material selection is wrong, and some molding process selections are unreliable, which will directly lead to their improper fixing.

 

Cixi Hongsheng Machinery Equipment Co., Ltd. is a high-tech enterprise specializing in R&D and manufacturing of automated wire harness end processing equipment and non-standard automation equipment. The company is located in Cixi City, Zhejiang Province, the economically developed south wing center of the Yangtze River Delta, bordering Ningbo City in the east, Yuyao City in the south, and Hangzhou Bay Bridge in the north. The transportation is convenient. Very good.

After decades of development and technology precipitation, the company has domestic leading independent core technology, advanced production equipment and perfect management system. It has won the trust and support of domestic and foreign customers with excellent quality and good reputation. “Acer” won 86 national patents (18 of which were invention patents) and was recognized as a municipal key new product. The products were listed in Zhejiang Province’s first “machine substitution” advanced applicable equipment promotion catalogue. The company has passed the ISO9001 quality management system certification and has been recognized as a municipal-level enterprise engineering technology center, a municipal-level technology-based enterprise, and a national high-tech enterprise.

Under the new situation of “Tenglong for bird transformation, machine substitution for people to increase efficiency”, Acer has always been committed to providing intelligent products for product transformation and upgrading in the fields of home appliances, electric power, photovoltaics, new energy, automobiles and aviation. High precision automation equipment.