Cixi City Hongsheng Machinery Equipment Co., Ltd

Automatic wire stripping machine common fault solution

The line can not be stripped

1. Check the cutting depth of the line, and the adjustment line diameter value becomes smaller.

2. The gap of the incoming transmission wheel is too large, and the gap of the incoming transmission wheel is adjusted.

3. Whether the peeling head setting is greater than 2mm.

4, the inlet pipe has stolen goods.

5. The retraction setting is too large and needs to be reduced.

Cannot be stripped at the end of the line

1. Check the cutting depth of the line, and the adjustment line diameter value becomes smaller.

2. The clearance of the outgoing transmission wheel is too large, and the clearance of the transmission wheel of the outgoing line is adjusted.

3. Whether the peeling head setting is greater than 2mm.

4, the retraction setting is too large, need to be small.

Wire wound

1. Adjust the gap between the incoming line transfer wheel and the outgoing line transfer wheel.

2. Contact the factory and replace the transfer wheel.

The core is cut

1. Adjust the value of the wire diameter until the appropriate degree (the blade just cuts the thread but does not hurt the core is the best position).

2. If the line is very thin, it can not be peeled after being adjusted to the wire diameter, and the retraction value can be appropriately reduced.

Different lengths, actual line length is greater than or equal to the set line length

1. The gap of the incoming transmission wheel is too large, and sometimes the line is not peeled off. The line that the line can not be peeled off is larger than the set line length. Adjust the “line gap adjustment wheel” to increase the pressure.

2. There are stolen goods in the inlet pipe, please check and clean properly.

3. Adjust the pressure of the incoming line transfer wheel.

Different lengths, actual line length is less than or equal to the set line length

1. The thickness of the wire itself is different.

2, the rolling wheel has stolen goods, need to be cleaned. There is wax on the surface of the wire, causing the ingress and egress transmission wheels to slip.

3. Take out the line, the program is set to “00”, run dry, stop, check whether the “in and out line wheel” rotation is flexible or stuck.

4. There is a stuck phenomenon in the pay-off frame, which causes the input line to slip.

Some cores are too long

1. The wire diameter is too small, the cutting edge is cut to the core, and it is taken out when stripping the wire. It is necessary to increase the wire diameter value by 1-2.

2. The retraction setting is too small, and the retraction parameters should be increased appropriately.

Sometimes the wires are connected together without cutting off

1. Add oil to the active part of the knife edge and try again (usually every 8 hours of operation).

2. Slow down the speed and try again.

3. Check if the wire specifications are within the allowable range of this model. Sheathing equipment

4. Whether the blade becomes dull.

Tilting when cutting

1. The wire itself is too curved and needs to be straight.

2. The wire mouth is not facing the center of the knife edge.

【2019-03-19】
Automatic terminal machine detection method and dehumidification method and skill

1. The length of the peeling opening is different:

There are many reasons why the opening is different. The most common one is that the wire reel is too tight or loose; in this case, you only need to use the roller fine adjustment to adjust the gap between the two wheels so that the wire is not flattened and too loose. If it is because the cutting knife is too shallow or too deep; then we use the cutter depth adjustment member to adjust the knife edge to the appropriate position, so as not to damage the copper wire and can peel off the rubber. If the opening is still different, replace the new cutting blade directly.

2, pressing the terminal exposed copper wire uneven:

Check whether the gun-type swing arm pipe is attached to the wire; whether the terminal machine edge is relatively straight with the swing arm pipe; whether the terminal machine auxiliary clamp is loose; check whether the distance between the terminal machine and the automatic machine changes.

3. The terminal machine cannot start running or stop during operation:

Can not start or stop during operation, first of all to check whether there is no current input and 6KG air pressure and there is a wireless material or a certain operating part stuck; also check the terminal machine for signal connection or power connection and lead to the terminal machine is not pressed .

4. The length of the electronic wire cutting of the terminal machine is inconsistent:

It may be the tangential edge wear or the knife edge; the problem with this is simply to replace the new cutter. The possible reason is because the wire reel is too tight or too loose; at this time we can use the roller fine adjustment to adjust the gap between the two wheels so that the wire is not flattened and too loose.

Some methods and techniques for dehumidification of fully automatic terminal machines

However, any electronic products of the fully automatic terminal machine will encounter some problems more or less during use. These problems are likely to affect the use of the machine and reduce the life of the machine. One of the most important and most common problems is "dehumidification", so how to dehumidify it. Summarize the following points and hope to help you!

1. Drain with air conditioner. Most of today’s air conditioners have this function. The dehumidification function of the air conditioner can be activated to effectively deal with the problem of humidification of the room during the rainy period, and the full-automatic terminal machine can also constitute an all-round maintenance.

2. When the factory’s fully automatic terminal machine is not in use, it is better to make a maintenance cover, which can effectively prevent the rear part of the appliance from contacting the humid air. At the same time, you can also improve the frequency of using these appliances, because the machine will generate heat when it is running, so that it can effectively dissipate moisture. If the computer can’t show up due to humidity, you can turn it on and the projector will be able to work again in about 10 minutes.

3, if the outside air is too humid, remember to close the door and close the window; if the house is too humid, to ensure the room ventilation, you can use air conditioning, fan to dehumidify.

4, if the wall is "sweat", it is recommended to purchase dehumidifier dehumidification. It is best to use an industrial dehumidifier

5. For long-term moist areas, it is possible to use charcoal in the room or bamboo charcoal under the indoor floor. The balance of humidity in the room and the prevention and control of dust mites and air purification have good effects. Ordinary factory buildings are best covered with cardboard boxes in the air.

6. Put some quicklime (mixed with sand) in the dead corners.

【2019-03-16】
Whether the quality of the terminal machine is qualified or not, from which details can be known

Whether the terminal is qualified or not is required to pass through the terminal section analyzer. The process is divided into: cutting----polishing----electrolysis (corrosion)----observation.

1. The length of the peeling opening is different: there are many reasons why the opening is different. The most common one is that the feeding wheel is too tight or loose; at this time, you only need to use the roller fine adjustment to adjust the gap between the two wheels so that the wire is not Squash and too loose. If it is because the cutting knife is too shallow or too deep; then we use the cutter depth adjustment member to adjust the knife edge to the appropriate position, so as not to damage the copper wire and can peel off the rubber. If the opening is still different, replace the new cutting blade directly.

2. Unevenness of the exposed copper wire of the crimping terminal: Check whether the gun-type swing arm pipe is attached to the wire; whether the terminal machine blade is relatively straight with the swing arm pipe; whether the terminal machine auxiliary clamp is loose; check the terminal machine and the automatic machine There is no change in the distance between them.

3. The terminal machine can’t start running or stop during operation: it can’t start or stop during operation. First of all, it must be checked whether there is no current input and 6KG air pressure and there is a wireless material or a running part stuck; also check whether the terminal machine has signal The connection or power connection leads to the terminal and the machine does not press.

4. The length of the electronic wire cutting of the terminal machine is inconsistent: it may be the cutting edge of the cutting edge or the edge of the knife edge; the problem is simply to replace the new cutting knife. The possible reason is because the wire reel is too tight or too loose; at this time we can use the roller fine adjustment to adjust the gap between the two wheels so that the wire is not flattened and too loose.

【2019-03-16】
Advantages of terminals used in fully automatic terminal machines

With the continuous expansion of the application range of terminal machines, its market demand is also increasing, and more and more companies producing fully automatic terminal machines are available. Automatic stripping machines can be used for automatic stripping, and work efficiency can be improved. At the same time, it can also reduce manual labor, avoid waste of human resources, and create more wealth for enterprises. Let us talk about the advantages of the terminals used in automatic terminal machines:

Regardless of the type of connection terminal, they all have the following advantages

1. The welding pin is made of copper alloy, and the welding pin has no dirt to ensure long-term reliability of welding.

2. The clamping body and the welding pin are mechanically decoupled, that is, because the clamping body and the welding pin are not connected together, the torque when tightening the screw is not transmitted to the solder joint.

3. The end of the welding pin is shortened and made easy to install.

4. With cooling channel.

5. Tinned solder pins for easy soldering.

6. Large wiring capacity, can be used to a variety of wiring needs.

7. The solder pins are quadrangular and the ends are shortened and tapered. When piercing the weld hole, it can prevent random transformation. Use solder bath to dissolve into the solder hole.

Users can not only select different parameters of the terminal machine according to the requirements, such as needle position, stitch length, etc., but also select different wiring directions. In practice, component planning (such as the orientation of the PCB in the housing) often constrains the printed circuit board terminals.

【2019-03-12】
The importance of high quality terminal machines

Choosing quality equipment not only makes the company profitable, saves manpower, but also enhances the corporate image and is widely recognized in the industry. The automatic terminal machine is also called automatic peeling and pressing machine. It is the function of feeding, cutting and other functions. The terminal machine wire feeder is used with the automatic terminal machine. The wire stripping machine is equipped with automatic computer. The stripping machine is suitable for use. The stripping machine is suitable for the wire stripping machine. The wire is sent to the stripping machine for smoother and faster feeding. So choosing a high-quality fully automatic terminal machine is the key to your success.

The terminal machine can be classified into a fully automatic terminal machine, a stripping terminal device, an ultra-quiet terminal machine, a pneumatic terminal machine, a terminal block machine, a computer line automatic peeling and ending machine, a pin machine terminal machine, a gold wire terminal machine, and the like.

The operation process of the fully automatic terminal machine is relatively simple, because it is a fully automatic way, so it is more labor-saving. First, turn on the power terminal switch, and the power indicator light starts to use it. The hand must be better than the blade support tool. The knife is correct. After the knife is finished, you must use the manual test. You need to hit the terminal equipment. The hex wrench adjusts the use of the feed plate so that the terminal can pass easily. The terminal operator must check whether there are plastic bags, hangs, etc. during the production process, and one terminal pull test every hour.

【2019-03-12】
Shanghai Munich electronic production equipment exhibition

My company decided on March 17, 2015 - 19, to participate in the Shanghai Munich electronics production equipment Expo, the company will launch a series of new automation products, pavilion number: E2, booth number: 2642, warm welcome new and old customers to visit!

Address: Shanghai New International Expo Center [Pudong New Area No. 2345 Longyang Road (near Fangdian Road)]

【2016-11-14】

Home 1 2 3 4 5 678 9 End

Service hotline：0086-574-63315122

【2019-03-19】

【2019-03-16】

【2019-03-16】

【2019-03-12】

【2019-03-12】

【2016-11-14】